Tri-Vista
A3.2 Series
A308 Series
A5 Series
kW Series
PreAmplifier
Power Amplifier
Integr.Amplifier
Phono Stage
MonoAmp
A324
DAC
<<
назад
Серия kW
kW
предварительный усилитель
OUTPUT
Voltage RMS
> 62 Volts
Peak-to-peak
output current
4.5 Amps
Impedance
< 0.5 Ohm
Frequency response
20Hz to 30kHz ±0.5dB
LINE INPUTS
Total harmonic distortion
+ noise 20Hz to 20KHz
< 0.0068% (5 Volts output,
maximum volume)
Signal / noise ratio
> 105dB ( 'A'-weighted, at half volume)
Input sensitivity
for 250 Watts into 8 Ohms
240mV
Input impedance
500k Ohms
Gain
at maximum volume
12.5dB (4.2 times)
Overload margin
35dB for rated input at maximum
volume
Channel separation
> 84dB 20Hz to 20kHz, maximum
volume
Channel balance error
< 0.5dB typical, worst
case 1.5dB with volume control at around
8 o`clock position
GENERAL
Input impedance
47k Ohms
Overload margin
24dB
Inputs
4 pairs line level RCA connectors,
1 pair (Home Theatre) direct power amplifier
input RCA connectors
Outputs
1 pair RCA main output controlled
by the volume,
1 pair RCA tape record fixed line level
output.
Overload margin
24dB
Inputs
4 pairs line level RCA connectors.
1 pair (Home Theatre) direct power amplifier
input RCA connectors.
1 pair phono (moving magnet) RCA connectors.
Power
requirement
115 / 230Volts or 100V AC
50 / 60Hz (factory pre-set), 60 Watts
Weight
20.55kg, 45.3 lbs unit only,
unboxed
25.5kg, 56.2 lbs in shipping carton
Dimensions
483 mm, 19 inches wide
167 mm, 6.6 inches high including feet
450 mm, 17.7 inches deep including knob
and rear terminals
Standard
accessories
IEC type mains lead (10-Amp
type),
remote control (kW universal type),
2 batteries size LR03 or AAA, manganese
alkaline type
kW
750 усилитель мощности
Power
750 Watts per channel into 8 Ohms (29dBW),
1100 Watts per channel into 4 Ohms
Voltage, RMS
77.5 Volts 20Hz to 20kHz
Voltage, peak-to-peak
219 Volts
Current, peak-to-peak
250 Amps
Damping factor
204
Output devices per
channel
20
Loop out impedance
50 Ohms
LINE INPUTS
Total harmonic distortion
+ noise
< 0.004% 20Hz to 20kHz
Signal / noise ratio
> 124dB "A"-weighted
Input sensitivity
for 750 Watts into 8 Ohms
2.4 Volts
Input impedance
100k Ohms
Channel separation
> 93dB typical
Frequency response
20Hz to 20kHz, +0, -0.2dB
GENERAL
Input
1 pair line level RCA connectors
Outputs
2 amplifier channels via 2 pairs per channel
binding posts, 1 pair RCA loop output sockets
Power requirement
100 / 115 / 230Volts AC 50 / 60Hz (factory
pre-set),
2500 Watts at maximum audio power into 8
Ohms, 290 Watts idle
DIMENSIONS
Amplifier
483 mm, 19 inches wide
167 mm, 21.8 inches high including feet
553 mm, 15.75 inches deep including rear
terminals
Power supply
364 mm, 14.4 inches wide
167 mm, 6.6 inches high including feet
278 mm, 11 inches deep including rear sockets
WEIGHT
Amplifier
34.1 kg, 75.1 lbs unit only, unboxed
45.2 kg, 100 lbs in shipping carton
Power supply
18.4 kg, 40.6 lbs unit only, unboxed
21.4 kg, 47.2 lbs in shipping carton
STANDARD
ACCESORIES
IEC mains lead -
(16-Amp type)
one, 2.4 metres (94.5 inches)
Low voltage interconnection
leads
two, 1.2 metres (47.3 inches)
Control interconnection
lead
one, 1.2 metres (47.3 inches)
kW
500 интегральный усилитель
<<
назад
Power
510 Watts per channel into 8 Ohms (27dBW),
770 Watts per channel into 4 Ohms
Voltage, RMS
63.9 Volts 20Hz to 20kHz
Voltage, peak-to-peak
180.6 Volts
Current, peak-to-peak
160 Amps
Damping factor
> 200
Output devices per
channel
8
Pre-output impedance
50 Ohms
PHONO INPUT
Frequency response
reference IEC, RIAA
(see graph below)
Signal / noise ratio
> 96dB moving magnet ?A?-weighted
Input sensitivity
2.5mV (moving magnet)
Input impedance
47k Ohms
Overload margin
29dB
Inputs
5 pairs line level RCA connectors,
1 pair phono (moving magnet) RCA connectors.
Outputs
2 amplifier channels via 2 pairs per channel
binding posts,
1 pair RCA audio pre-outputs controlled
by the volume setting,
1 pair RCA tape record fixed line level
output.
Power requirement
100 / 115 / 230Volts AC 50 / 60Hz (factory
preset),
1950 Watts maximum into 8 Ohms.
Weight
main unit
26.8kg, 59lbs unit only, unboxed
31.8kg, 70.1lbs in shipping carton
Weight PSU
18.3 kg, 40.3 lbs unit only, unboxed
21.3 kg, 47 lbs in shipping carton
Dimensions main unit
483mm, 19 inches wide
167mm, 6.6 inches high including feet
470mm, 18.5 inches deep including
terminals
Dimensions PSU
364mm, 14.4 inches wide
167mm, 6.6 inches high including feet
278mm, 11 inches deep including terminals
Standard accessories
IEC type mains lead (10-Amp type),
Power supply leads, main (two),
Power supply lead for pre-amplifier,
Remote control (universal type),
Two batteries size LR03 or AAA, manganese
alkaline type
kW
Phono Stage
OUTPUT
Voltage RMS, maximum
> 43 Volts
Impedance
32 Ohms
Frequency response
deviation from RIAA
20Hz to 20kHz ±0.1dB
LINE INPUTS
Total harmonic distortion
+ noise 20Hz to 20KHz
< 0.012% (MM, 10 Volts
output)
Input sensitivity
for
300mV RMS output
2.9mV Moving Magnet, 500µV
Moving Coil
Input impedance
MC: Switched, 10 Ohms or 100
Ohms in parallel with 470pF
MM: All switches up : 68k Ohms in parallel
with 47pF,
- Switch no. 1 down : 47k Ohms + 47pF,
- Switch no. 2 down : extra 50pF added,
- Switch no. 3 down : extra 100pF added,
- Switch no. 4 down : extra 200pF added
Overload margin
42dB above rated input at
1kHz (MM)
Channel separation
> 64dB 20Hz to 20kHz
Channel balance error
< 0.5dB typical
Signal / noise ref.
1Volt RMS output
> 78dB Moving Magnet (?A?-weighted)
> 75dB Moving Coil (?A?-weighted)
Frequency response
reference IEC, RIAA
- see graph . . . .
GENERAL
Input sockets
2 phono Moving Magnet via
RCA connector
2 phono Moving Coil via RCA connector
Output sockets
2 RCA connectors for line level output
Power requirements
115 / 230 Volts or 100 V AC
50 / 60Hz (factory preset) 25 watts maximum
Dimensions
483mm, 19 inches wide
167mm, 6.6 inches high (including feet)
456mm, 18 inches deep (including buttons
and rear terminals)
Weights
18.15Kg, 40 lbs unit only,
unboxed
23Kg, 51 lbs in shipping carton
Standard accessories
IEC mains lead - 10 Amp type
Новости Продукция
Статьи О
компании Ссылки